Focus on heavy equipment

Symons Cone Crusher

Symons Cone Crusher

  • Capacity: 27-1814 t/h
  • Heat source: Biomass, natural gas, propane, diesel, coal, etc.

Environmental: Multi-level dust removal and environmental protection standards

Leave Us A Message

Introduction

Symons cone crusher is also called compound stone cone crusher. It's semi hydraulic and semi spring cone crusher to crush mid-hard and above mid-hard ores and rocks efficiently. Symons crusher is popular stone crusher in aggregates production plant.

Simmons cone crusher is an improved, optimized and updated replacement product of spring cone crusher. Based on the principle of laminated crushing, it has developed into a modern high-performance cone crusher integrating high swing frequency, optimized cavity shape and reasonable stroke. CS cone crusher is suitable for various coarse, medium and fine materials whose compressive strength does not exceed 350MPa, such as river pebbles, granite, basalt, iron ore, shale, limestone, coal gangue, quartz, diabase, marble, copper ore, pebbles, etc.

structure of Symons cone crusher

structure of Symons cone crusher

Principle

Cone crusher is a compression type of stone crusher. The feeding rock is crushed by squeezing or compressing the feed material between a wear resistant mantle and a manganese concave or a bowl liner. The mantle is a moving part that gyrates in an eccentric motion though an eccentrically gyrating spindle.

When rock enters the top of the cone crusher, it is squeezed between the mantle and the bowl liner or concave, as the eccentric spindle rotates to cause the compression within the chamber. The material gets smaller as it moves down through the wear liner as the opening in the cavity gets tighter. Large pieces of ore are broken once, and then fall to a lower position where they are broken again. This process continues until the pieces are small enough to fall through the narrow opening at the bottom of the crusher. Final sizing and reduction is determined by the closed side setting or the gap between the two crushing members at the lowest point.

The Symons cone crusher is adjusted by spinning the bowl up or down manually or through hydraulic rams. A series of powerful springs give the necessary tramp protection without damage to the crusher.

Advantage

1. Through the optimized design of the cavity and the combination of reasonable speed and stroke, CS cone crusher can perform the most work under the same diameter of the moving cone. Therefore, compared with the same type of spring cone crusher, it has higher performance and production capacity.

2. Based on the principle of lamination crushing, the proportion of cubes in the crushed s tone product is significantly increased, the needle-like stones are reduced, and the particle size is more uniform.

3. When unbreakable materials enter cone crusher crushing chamber, high-performance alloy steel springs are used as advanced overload protection system, it can effectively protect machine safety.

4. The automatic control system adopts large-diameter main shaft, heavy-duty main frame and independent thin oil lubrication system to ensure that the equipment is durable and reliable in operation.

Symons Cone Crusher
Symons Cone Crusher
Symons Cone Crusher

Parameters

Model Cavity type Crushing cone dia.(mm) Adjusting Range of
Discharge Opening(mm)
Max feeding size(mm) Power(kw) Capacity(t/h) Overall size(mm)
CS75 C 900(3') 13-38 150 75 59-163 2656×1636×2241
CS75 M 900(3') 9-22 85 75 45-91 2656×1636×2241
CS75 F 900(3') 3-13 35 75 27-90 2656×1636×2241
CS110 C 1200(4') 19-50 180 110 110-250 2821×1974×2651
CS110 M 1200(4') 13-38 130 110 80-180 2821×1974×2651
CS110 F 1200(4') 9-31 90 110 63-140 2821×1974×2651
CS160 C 1295(4 1/4') 19-51 205 160 172-349 2983×1866×3156
CS160 M 1295(4 1/4') 16-38 178 160 132-253 2983×1866×3156
CS160 F 1295(4 1/4') 13-31 115 160 109-181 2983×1866×3156
CS220 C 1400(4 1/2') 30-60 235 220 210-530 3360×2650×3050
CS220 M 1400(4 1/2') 22-45 180 220 180-475 3360×2650×3050
CS220 F 1400(4 1/2') 19-40 100 220 130-260 3360×2650×3050
CS250 C 1650(5 1/2') 25-64 228 250 299-635 3941×2954×3771
CS250 M 1650(5 1/2') 22-51 205 250 258-417 3941×2954×3771
CS250 F 1650(5 1/2') 16-38 178 250 181-327 3941×2954×3771
CS315 C 2135(7') 31-64 315 400 1125-1814 4613×3302×4638
CS315 M 2135(7') 25-51 284 400 862-1424 4613×3302×4638
CS315 F 2135(7') 19-38 236 400 544-1034 4613×3302×4638

 

Leave Us A Message

We will contact you as soon as possible

Hot Products Wechat/WhatsApp:+86 156-1759-1790

LEAVE US A MESSAGE

Old Customer Message
  • Mrs Rose*** 2022-08-20

    I would like to ask for a price quotetion for 100 ton per hour sand washing machine.

  • Mr Nicol*** 2020-10-18

    We need dryer for river sand, 10 tons/hr.

  • Mr Musta*** 2023-1-21

    Please send offer for VSI-1145 sand making machine

  • Mr Bong*** 2022-11-16

    I am going to order a 3 way drum dryer for concrete industry, what's price?

  • Mr Geor*** 2023-01-15

    We are intrested in drum dryer for quartz stone, we need a high capacity.

  • Mr Kaml*** 2022-02-03

    I'm required Clay dryer 100MT/ Day.

  • Mr Gabr*** 2021-02-18

    Dryer quote requored for drying flyash having 5% moisture.

  • Mr Boja*** 2021-03-06

    Interested in your jaw crusher, model-SKJ8711. What's price?

  • Mr Azha*** 2022-04-07

    We require a sludge drying system for our Effluent treatment plant.

  • Mr Ngab*** 2022-04-21

    We require a drying drum for drying lame concentrate with a moisture content of 10%, with a capacity of 50 tons per hour

  • Mr Subh*** 2021-05-23

    Sand drying machine price and advise.

  • Mrs Mshe*** 2021-06-25

    What is the max capacity of your screw sand washing machine?

  • Mr Sams*** 2021-07-17

    please share us the Raymond Mill profile

  • Mr Siva*** 2021-08-06

    I required sand drier machine use for foundry application